2026-11-19

Troubleshooting Guide: Common blow molding Problems and Solutions

Blow molding defects such as uneven wall thickness and neck deformation, plus feeding problems and air leaks, can increase scrap, downtime, material and energy waste, and delivery delays. This guide covers causes, solutions, and prevention tips to help you resolve problems, maintain quality and efficiency, control costs, and reduce losses.

Common Blow Molding Defects and Solutions

Two-Stage PET Stretch Blow Molding Troubleshooting

Quality / Production DefectMain CausesTroubleshooting and Adjustments
1. Bottle Haze from CrystallizationExcessive preform heating causes PET to crystallize too much.
  1. Lower the overall oven temperature or reduce the heating lamp voltage.
  2. Improve oven ventilation and cooling to prevent surface overheating.
2. Base Rupture / Insufficient Stretching
  1. Pre-blowing starts too late, or the pre-blow pressure is too low.
  2. The stretch rod does not reach the bottom, or the preform base is not heated enough.
  1. Start pre-blowing earlier or increase the pre-blow pressure.
  2. Increase the power of the heating lamps that heat the preform base.
  3. Check the stretch rod stroke and pneumatic cylinder pressure.
3. Uneven Bottle Wall Thickness / Thin Spots
  1. The preform is heated unevenly around its circumference.
  2. Incorrect pre-blow timing: starting too early creates thin spots, while starting too late prevents proper stretching.
  1. Check whether the preform rotation mechanism in the oven is sticking or jammed.
  2. Fine-tune the pre-blow timing and the switch to high-pressure blowing.
4. Neck Deformation / Thread DamageInadequate neck cooling in the oven allows heat to reach and soften the neck.
  1. Check the neck cooling water lines and air ducts for blockages.
  2. Move the heating lamps farther away from the threaded neck area.
5. Bottle Folding / Vertical Wrinkles
  1. Excessive pre-blow pressure causes the preform to expand faster than the stretch rod moves downward.
  2. Excessive heating makes the preform too soft.
  1. Lower the pre-blow pressure or delay pre-blowing.
  2. Moderately reduce the overall heating power.

HDPE / PP Extrusion Blow Molding (EBM) Troubleshooting

Quality / Production DefectMain CausesTroubleshooting and Adjustments
1. Vertical Streaks / Flow Marks on the BottleCarbonized material or contaminants inside the die head, or scratches on the die opening.
  1. Use a copper strip to remove residue from the die opening. Do not scrape the die head with hard metal tools.
  2. Raise the barrel temperature and purge at high speed.
2. Excessive Flash / Material Overflow at the Neck
  1. Insufficient clamping force.
  2. Worn mold parting surfaces.
  3. The parison wall thickness is set too high.
  1. Increase the mold closing and clamping pressure.
  2. Reduce the parison wall thickness setting in the pinch-off area.
  3. Check whether the mold mating surfaces need to be refinished.
3. Thin Bottle Walls / Rupture at the Pinch-Off Seam
  1. Incorrect parison thickness profile settings.
  2. Excessive sagging stretches and thins the parison.
  1. Increase the die gap setting for the corresponding section of the parison profile.
  2. Lower the die head temperature or use a resin with a lower melt flow index (MFI) to reduce sagging.
4. Bubbles in the Bottle WallHigh moisture content in the material, or air trapped during melting.
  1. Dry the material again. HDPE is typically dried at 80°C for 2 hours.
  2. Check whether the screw back pressure is too low.
5. Product Shrinkage and Warping / Inconsistent Dimensions
  1. Insufficient or uneven mold cooling.
  2. Cooling time is too short.
  1. Check cooling water flow and temperature, and clear blocked cooling channels.
  2. Extend in-mold cooling time as needed.

Practical Tips for Preventing Problems

PET Stretch Blow Molding Machine

1. Equipment and Temperature Control Management

Calibrate the oven heating lamps and barrel heater bands monthly to prevent differences between displayed and actual temperatures. This prevents uneven preform heating, which can cause wall thickness variations or PET whitening from crystallization.

Clean mold and neck cooling channels quarterly and install water flow and temperature sensors to help prevent scale-related blockages, neck overheating and deformation, and longer cycles.

2. Air Circuit and Pressure System Management

Weekly inspection of the high-pressure air lines and replacement of the water and oil filter elements are recommended. This helps prevent moisture and oil from contaminating polished mold surfaces or causing valves to stick and delay blowing.

Before daily startup, perform a pressure-hold test for small leaks in the blow valve block and air fittings. This helps prevent pre-blow pressure instability and resulting base rupture during stretching, while reducing air waste.

3. Raw Material and Drying Management

Before melt processing, dry PET pellets to supplier specifications and check moisture content. Protect two-stage stretch blow molding preforms from moisture; do not apply pellet drying conditions to them. Keep HDPE free from surface condensation and contamination.

For post-consumer recycled (PCR) material, record batch inspections and blending ratios. Use gravimetric dosing as needed to reduce material-related quality variations.

4. Mold and Mechanical Structure Maintenance

Before each shift ends, clean mold vents and pinch-off areas with a copper brush and dedicated cleaner. This helps prevent trapped air and flash-area buildup that obstructs mold closure and overloads the clamping mechanism.

Regularly lubricate the stretch rod guide rails and mold opening and closing crankshaft with food-grade grease. Also, check the stretch rod alignment regularly to prevent a misaligned rod from puncturing the bottle base or worn guide rails from causing bottle jams.

5. Digitalization and Smart Prevention

Digitally store and lock each bottle design’s validated settings, including heating power, pre-blow and main blow timing, and wall thickness profiles. This prevents unauthorized changes and allows direct loading during mold or line changeovers, speeding mold trials and maintaining yield.

Facilities with the resources can also introduce AI vision inspection alongside servo motor current and vibration monitoring. These systems can detect abnormal trends early and provide warnings before problems worsen or equipment fails, reducing the risk of unplanned downtime.

Blow Molding Troubleshooting FAQ

Q1. How can I address leaks caused by neck deformation or thread damage?

In two-stage PET stretch blow molding, neck deformation may result from excessive heat exposure or inadequate neck cooling. Check the neck cooling system and heating lamp positions. For thread damage, also inspect preform quality and handling components for mechanical damage.

Q2. How can I quickly troubleshoot frequent bottle jams, tipping, or dropping?

Common causes include misaligned grippers, incorrect bottle transfer timing, or deformed necks that impair gripping. Check grippers for loose springs, wear, or oil buildup. Recalibrate sensor timing for bottle infeed, outfeed, and mold opening and closing. Allow sufficient exhaust time: residual high-pressure air may eject bottles during mold opening and cause jams.

Conclusion

Effective blow molding troubleshooting combines systematic material, equipment, and process checks with preventive maintenance. Recording issues and continuously optimizing processes reduces recurring problems and improves yield and efficiency.

Full Shine develops, designs, and manufactures high-performance automatic extrusion, PET stretch, and single-stage injection blow molding machines. Their efficient, precise, and consistent processing of various plastics has earned customers’ trust worldwide.

For stable output and reduced scrap, consider these blow molding equipment options:

  • FS-4000AD PET Stretch Blow Molding Machine: Its 4-cavity design produces up to 4,000 bottles per hour. Advanced cooling and touchscreen controls support high-volume production of PET containers, including mineral water and shampoo bottles.
  • P Series Automatic Extrusion Blow Molding Machine: Produces 20 mL–30 L containers with 1–12 cavities. Available in single- or double-station configurations, it supports PE, PP, PETG, PVC, ABS, PA, PS, co-extrusion, parison wall thickness control, and automatic deflashing.

If you'd like to learn more about machine specifications or evaluate your production line needs, feel free to contact Full Shine. You can also visit the FAQ page for more information on equipment maintenance and troubleshooting.